Side-Grip High-Frequency Pile Driver

side grip pile driving attachment
side grip pile driving attachment
side grip pile driving attachment
side-grip high-frequency pile driver
side-grip high-frequency pile driver

If you have tried to drive steel sheet piles inside narrow foundation pits, next to existing buildings, or under overhead structures, you already know the limits of traditional top-clamp vibro hammers. Top-grip pile drivers need clear vertical space above the pile to clamp and operate. When overhead space is limited, the hammer cannot fit, and you may face delays, expensive site redesign, or risk damaging the pile top during clamping. Our side-grip high-frequency pile driver solves this pain point: it clamps the steel pile from the side, instead of grabbing the top, so it can work when there is no clearance above the pile.

A side-grip high-frequency pile driver is a hydraulic vibro attachment mounted on an excavator. It uses high-frequency vibration to drive or extract steel piles into and out of soil. Unlike top-clamp models, its clamping jaws grip the side wall of the pile. This design lets operators install piles in confined zones, adjust pile angle freely, and avoid crushing or deforming the pile top. This attachment fits excavators ranging from 20 tons to 50 tons, and works for steel pile diameters from 180 mm to 630 mm.

Send your excavator model, pile dimensions, and soil information. We can assess the attachment, clamp arrangement, and hydraulic requirements before preparing a quotation.

Get Your Free Quote in 12 Hours

Technical Parameters of the YG Side-Grip High-Frequency Pile Driver

Data/ModelYG45YG55YG65YG75
Eccentric Moment (Kgm)4.65.56.57.5
Centrifugal Force (KN)268320378451
Max Centrifugal Force (KN)455545645767
Frequency (rpm)2300-30002300-30002300-30002300-3000
Side Clamp Force (KN)332382456558
Bottom Clamp Force (KN)384384550550
Hydraulic System Operation Pressure (bar)300300320320
Rotate/Tilt Degree (°)360/±30360/±30360/±30360/±30
Size (mm)1320*1450*25501320*1450*25501350*1490*26501350*1490*2650
Weight (Kg)2300260032003500
Excavator Weight (T)20-2525-3232-4040-50

Applicable Steel Pile Diameter: 180-630mm

Find the Right Model for Your Sheet Pile Size – Free Consultation

high-frequency vibratory pile driver
high-frequency vibratory pile driver
high-frequency side grip pile driver
high-frequency side grip pile driver

Side-Grip vs Top-Clamp High-Frequency Pile Driver: How to Choose

Many buyers confuse these two vibro hammer types, and picking the wrong one will stop your job on site.

  • Side-grip high-frequency pile driver: Clamps from the side. It does not require overhead clearance above the pile. It supports 360° rotation and ±30° tilt, great for inclined piles, tight pits, and areas with overhead barriers. It is the better pick for urban renovation, inner foundation pit work, and limited-space sites.
  • Top-clamp high-frequency vibro pile driver: Clamps the top of the pile. It delivers stable performance on open sites, large waterfront cofferdams, and open land piling jobs, where vertical space is fully available. It is usually preferred for fast, mass piling on unobstructed ground.

We supply both versions. If you mostly work in open waterfront areas, our top-clamp high-frequency vibro hammer is a matching option. If you also need to pull piles out after construction, our pile extractor can be paired for your full-cycle foundation work.

Key Advantages of YG Side-Grip High-Frequency Pile Driver

  1. Zero requirement for overhead clearance: The side clamping structure eliminates the need for open space above the pile, which is the biggest advantage for inner pit construction.
  2. 360° rotation plus ±30° tilt adjustment: You can align the pile vertically or set it to an inclined angle for slope reinforcement, without moving the excavator frequently.
  3. Dual clamping force: Separate side clamp force and bottom clamp force keep the pile fixed firmly during vibration, preventing slipping under high centrifugal force.
  4. Stable high-frequency vibration: Working frequency stays at 2300–3000 rpm, suitable for most sand, silt, and soft clay layers.
  5. Flexible excavator matching: Multiple models cover 20–50 ton excavators, so you can select a unit matching your existing fleet instead of renting extra-large piling machinery.

Side-Grip vs. Top-Type: Which Fits Your Site?

excavator side grip pile driver
excavator side grip pile driver
side grip pile driver
side grip pile driver

6 Application Scenarios of the YG Side Grip Vibratory Hammer

This side-grip vibro pile attachment is built for jobs where conventional piling equipment cannot enter:

  1. Foundation pit support: Sheet pile driving inside deep, narrow pits for building basement excavation.
  2. Municipal trench support: Steel pile retaining walls for underground pipeline, sewer, and cable projects in crowded urban zones.
  3. Slope and embankment reinforcement: Inclined steel piles for riverbank and road slope stabilization.
  4. Cofferdam construction in restricted zones: Waterfront projects with nearby structures that limit overhead working space.
  5. Urban reconstruction and renovation: Piling work beside old buildings, where overhead wires and narrow yards block top-clamp hammers.
  6. Temporary retaining wall and pile extraction: Drive piles for temporary support, then extract them once the project finishes.

Will It Match Your Excavator?

We can assess configurations for mainstream excavator brands, including CAT, Komatsu, Hitachi, Volvo, SANY, and XCMG.

Brand and tonnage are only the first screening step. Before confirming compatibility, provide:

  • Exact excavator model and boom configuration.
  • Available auxiliary flow and pressure.
  • Hydraulic return arrangement.
  • Mounting or quick-coupler dimensions.
  • Pile weight and length.
  • Intended working radius.
  • Ground and working-platform conditions.

The carrier must safely handle the attachment and the approved pile-handling arrangement. A nominal 30-tonne excavator does not automatically qualify for every operation associated with a 30-tonne-class attachment.

Talk to an Engineer Now – Free Consultation

side clamp pile driver
side clamp pile driver
excavator-mounted side grip pile driver
excavator-mounted side grip pile driver

Frequently Asked Questions About High-Frequency Pile Drivers (Side-Grip Attachments for Excavators)

Q1: Side-grip or top-clamp pile driver, which one should I pick?

A1: Choose side-grip if you work inside pits, near buildings, or have limited overhead space. Choose a top-clamp vibro hammer for open-site, large-scale piling jobs with enough vertical clearance above piles.

Q2: Can this side-grip model extract steel piles as well?

A2: Yes, it can drive and extract steel piles. If you have heavy, deep pile extraction work, we can also recommend our dedicated pile extractor for higher pulling capacity.

Q3: What is the minimum overhead space required for this side-grip pile driver?

A3: It only needs clearance for the attachment body itself, no extra space above the pile top. This is its core advantage for confined foundation pit projects.

Q4: What types of piles can this attachment handle?

A4: It works for steel sheet piles, steel pipe piles, and H-beam piles within the 180–630 mm diameter range.

Q5: Do I need to modify my excavator hydraulic system?

A5: We review your excavator hydraulic data before providing a quotation. Some machines require an auxiliary hydraulic circuit. We will inform you of modification requirements in advance.

Q6: How to get spare parts after delivery?

A6: We stock core wear parts including clamping jaws, vibration bearings, and hydraulic seals. We can ship spare parts separately and provide technical drawings for local maintenance support.

    Please feel free to give your inquiry in the form below. We will reply in 24 hours.

    Product Model:

    Your Name(required):

    Your Email(required):

    Your Phone(required):

    Your country:

    Your Whatsapp(required):

    Your Message(required):

    Related Post